AEG Dishwasher Error Code 10

AEG Dishwasher Error Code 10: Understanding the Issue and How to Solve It

Getting an error code flashing across your AEG dishwasher may sound a bit stressful. Well, don’t panic when you have been going through error code 10, because you aren’t the only one. The display gives signals that the drainage of water needs attention. On the good side, it allows showing that most often the problem can easily be sorted by oneself with just a bit of troubleshooting.

Here is everything you should know concerning error code 10, why it occurs, and how you can fix it step by step.

What does Error Code 10 Mean on an AEG Dishwasher?

Error code 10 in an AEG dishwasher usually means there is some fault with the water not draining, which could be due to blockage, a kinked drain hose, or even a problem with the pump. All the dishwasher does is find out that there is water in the tub when it shouldn’t be, then it fires off the error code to flag that issue.

What Causes the Error Code 10?

There can be numerous causes for error code 10. The most usual ones include, but are not limited to the following:

Blocked Filters – Particles of food and grease block the filters in the dishwasher and water does not drain efficiently.

Clogged Drain Hose – Kinking and blockage within the drain hose inhibit the smooth passage of water out of the machine.

Faulty Pump – The drain pump may be malfunctioning and not work right to remove water from the system.

Blocked Sink Drain – In cases where the dishwasher is sharing a drain with your sink, a blockage in the plumbing for the sink may also create issues with drainage for your dishwasher.

Incorrect Installation – The drainage system of your dishwasher may have not been installed correctly, which would make it create an issue with draining the water.

How to Fix Error Code 10

Now that you know the possible causes, here is a step-by-step guide to troubleshoot and fix error code 10:

1. Reset the Dishwasher

Sometimes, error codes are triggered due to temporary malfunctions. First, switch off the dishwasher and unplug it from the power source. After 10–15 minutes, plug it back in. This can “reset” the error code. If it persists, proceed to the next steps.

2. Check the Filters

Open the dishwasher and locate the filters at the bottom of the tub. Pull out the filters to have a good look at them for bits of food, debris, or grease built up on them. Clean the filters under running water and scrub off stubborn particles with a soft brush. Put the clean filters back to their original place.

3. Check the Drain Hose

Pull the dishwasher from underneath its position. Check for kinks and bends in the drain hose running from the dishwasher to the sink drain or standpipe. Take out the hose to check for blockages by running water through it. If you do find one, you could try clearing the blockage using a flexible cleaning brush or even a plumbing snake.

4. Clear the Sink Drain

If your dishwasher was connected to drain inside of your kitchen sink’s pipe, then a clog exists inside the drain of the sink. Run the hot water within the sink drain and will help smoothen small blockages. Use a drain cleaning tool or a professional plumber if blockages are serious.

5. Check Drain Pump

Ensure your safety -Switch off power to the dishwasher. Get access to drain pump – refer to your AEG dishwasher manual for instructions regarding how to access it. Inspect the pump for blockages or any symptoms that it could be malfunctioning, such as damage in any of the parts or an unusual humming sound when running. If the pump is damaged, replacement may be your best course of action. In this regard, it will be appropriate to contact a professional technician.

6. Verify Proper Installation

Make sure the dishwasher is installed correctly, the drain hose is at the correct height-it’s usually installed in a looping manner to prevent backflow. Check your dishwasher manual for any specific installation requirements.

7. Run a Test Cycle

After completing the above checks and cleaning, run an empty dishwashing cycle. Monitor the dishwasher closely to see if the error code appears again. If the error persists despite your efforts, the issue may require professional diagnosis.

When to Call a Professional

If all the steps of troubleshooting have been engaged in and the error code is still persistent, then it will be about time to consult professional repair services. The problem may be more complicated, like damaged circuit boards or internal wiring fault, requiring special tools and technical know-how for diagnosis and fixation.

How to Avoid Error Code 10 in the Future

To reduce the possibility of error code 10 occurring again, some precautionary measures can be taken:

Clean the Filters Regularly – Clean your dishwasher filters every week to avoid blockages.

Rinse Your Dishes – Scrape and rinse food particles off your dishes before placing them inside the machine.

Check the Drain Hose Periodically – Every few months, check the drain hose for kinks or blockages.

Use Dishwasher-Safe Drain Cleaners: Run the dishwasher-safe cleaners through the system once a month to keep grease and the build-up at bay.

Scheduling Maintenance: Schedule a once-a-year visit from a professional maintenance check and keep your dishwasher in top working order.

Conclusion

AEG dishwashers are designed to make our lives much easier, but issues do occasionally crop up with all kinds of appliances. The frustration with an error code 10 can thus be confidently handled through this guide now. Most other issues will resolve with only a little bit of patience and cursory inspection and thus avoid the irritant of actually calling in a repair.

If you ever doubt any of the steps, refer to your dishwasher’s manual for further guidance or consult a professional technician. After all, the smoother your dishwasher runs, the more time you will have to enjoy clean dishes and less time spent with error codes!

Click to rate this post!
[Total: 0 Average: 0]
Spread the love