Table of Contents
AEG Dishwasher Error Code 13 Explained-And How to Fix It
If your AEG dishwasher shows this code, you would probably like an idea of what’s meant and just generally how to rectify the appliance. Don’t be frustrated because we are there to help with what the code means and then take you through the steps one at a time to make sure that is resolved.
The following guide will go into detail on what Error Code 13 means, why it happens, and how you can go about fixing it. By the time you get to the end of this article, you should be confident to handle this issue or seek further assistance from professionals.
What Does AEG Error Code 13 Mean?
AEG dishwashers show error code 13 when there is an issue with the water draining system. More specifically, this would mean the dishwasher has detected water at the bottom of the appliance, which could be because of a leak or some malfunction of the draining mechanism.
Anyways, it is a precautionary device so that no further leakage or any other problem happens, but an error could just come out as a means to save your dishwasher and your family from certain hazards.
Possible Causes of Error Code 13
There are some grounds as to why there would be such accumulation of water which could originate this error signal. Common ones include:
Clogged or blocked drain hoses mean that food particles or debris block the way of drainage, and water cannot effectively leave the machine. Leaked internal components: Poor seals, broken hoses, or worn-out parts can cause water to drip into the bottom of the dishwasher. Faulty float switch: The float switch is responsible for detecting water in the base. If it’s malfunctioning, it may signal water accumulation where this is not actually the case.
Poor installation: If the appliance is installed poorly, it might be a reason for drainage or leakage problems sometime in the future. With these possible reasons, you will better understand why this error code would occur. Now, let’s head to the steps that you can do to resolve this issue.
How to Fix Error Code 13 on Your AEG Dishwasher
Whether you are confident around DIY works or this is the very first appliance-related care, this set of steps will guide you through an easily understandable process.
Step 1 – Turn Off and Unplug the Dishwasher
First, before making any repairs or investigating a possible fault in an AEG dishwasher, switch the machine off and unplug it from the electrical mains supply. This is important to prevent electric shock or some other form of accident, which can result in an injury while working.
Step 2 – Look for Visible Leaks
Pull the dishwasher from your space and try tracing signs of water leakage in that region. You may want to look for any pools or trickles under the appliance and into/around the hose attachments. If there is any leakage, mark out where this leakage occurs; this will thus narrow down your problem.
Step 3 – Check on the Drain Hose
Disconnect the drain hose and check whether something is blocking it or has been stuck inside it. Take a long flexible brush or flush it with water to remove the entrapped debris inside.
Do not let the hose kink or get damaged-that too would hamper the proper flow of water. Replace the drain hose if it is cracked or worn out.
Step 4-Filters and Sump Area Check
Open the dishwasher and pull out the bottom basket, then get access to filters and sump area – usually find beneath the spray arm. Give very strong cleaning on filters to make assure that no single piece of food partcle or greace which hinders flow of waters would remain their, check blockage in sum up-use a soft doth/clothes for picking up these obstacles.
Step 5 – FLOAT SWITCH Testing
The float switch monitors water levels at the bottom of your dishwasher. A sticking or malfunctioning float-a will falsely trip this error code.
Open the bottom and find the float, usually a round piece at the bottom. Gently lift it up and down; if this is stuck, then it may just need to clean the area where it goes up and down.
If it appears to be damaged, you’ll have to replace the float switch or call in a professional to assist.
Step 6: Run a Test Cycle
Once you’ve completed the inspections and cleaning steps, reconnect your dishwasher and rerun a short test cycle. Observe that the error code does not show up again for confirmation that the problem has been resolved.
When to Call a Professional
If the above steps fail to take care of your error code, then it’s time to call in a professional technician. Indeed, problems like internal seals going bad and electronic faults do take special skills and tools to be able to set right.
Most AEG appliances come with a warranty, so check your paperwork to see whether your dishwasher is covered for servicing or repairs.
Preventing Future Error Codes
To keep your AEG dishwasher running smoothly and avoid Error Code 13 in the future, consider these simple maintenance tips:
Regularly clean the filters and drain area to avoid clogs. Scrape off excess food from dishes before loading them into the dishwasher. Periodically check hoses and seals for wear and tear. Only use detergents designed for dishwashers to prevent build-up of residue.
Conclusion
AEG dishwasher Error Code 13 may be impossible to deal with in the very first few moments, but this is something most homeowners could fix if they had a bit of guidance on how to go about it. You can often diagnose and fix it yourself by being aware of the common causes and following some troubleshooting steps we will discuss here.
If you are not sure or do not feel confident to do the fix yourself, don’t hesitate to call a certified technician. An AEG dishwasher is an investment in convenience; making sure it works right will save time and energy over time.
Any tips or questions about how to fix dishwasher issues? Share below—your experience might help others in the same boat!