Table of Contents
How to Fix the Cove Dishwasher Error Code 800140
Dishwashers are designed to simplify your life-not spew out some crazy error codes that make your head spin. If you’re facing off with the Cove dishwasher error code 800140, don’t panic-you’re definitely not alone, and a remedy might be a whole lot easier than you anticipate.
The following blog post discusses what this code actually means, why it happens, and how one gets back to using his/her trusty dishwasher in no time.
What is the Meaning of Error Code 800140?
Error code 800140 on a Cove dishwasher usually means there is a problem with the drainage. The dishwasher is not draining the water as required during or after the wash cycle. This can be due to blockage, kinking of the drain hose, or a problem with the pump. While this sounds like something over which an alarm should be raised, most drainage problems can be fixed without calling in a professional.
Common Causes of Error Code 800140
To fix the issue, it’s essential to first understand what’s causing the problem. Here are some of the usual culprits that can trigger the 800140 code:
Clogged Drain Filter
Food particles, grease, or debris may have built up in the dishwasher’s filter, preventing water from draining properly.
Blocked Drain Hose
The drain hose carries wastewater away; this hose should not be kinked or clogged because it hampers the passage of water to its way out.
Faulty Pump
If the drain pump of the dishwasher is defective or clogged, then it would not be able to push the water out effectively.
Problem with Garbage Disposal Connection
For dishwashers installed along with a garbage disposal, it may be a case of blockage or incorrect installation.
Improper Placement of the Dishwasher
If the appliance is not at its level or has shifted a bit, this may obstruct the manner in which water flows out of the machine.
How to Fix Cove Dishwasher Error Code 800140
Here is a step-by-step guide to troubleshoot and resolve the issue. Put on some gloves and have a towel ready, as this may require some water handling.
1. Drain Filter Cleaning
Turn off the dishwasher and pull out the bottom rack. The drain filter is usually located at the bottom of the appliance. Twist it out, then rinse it under warm water to remove any debris, and wipe off any grease.
Reinstall the filter securely.
Helpful Tip: Make it a habit to clean your drain filter every month to avoid build-up.
2. Check the Drain Hose
Check that the hose is not kinked or bent. Straighten carefully. Disconnect the hose-you may have to use a bucket to catch any water that spills out-and check inside for obstructions.
Use a long brush or other flexible tool to clear blockages.
3. Check the Garbage Disposal Connection
If your dishwasher is connected to a garbage disposal, ensure that the knock-out plug on the disposal’s inlet has been removed-common if the installation is new. Check for blockages at the connection point and clean if necessary.
4. Check the Drain Pump
If cleaning the filter and hose didn’t work, the problem might be with the drain pump itself. Remove the toe/kickplate at the bottom of your dishwasher. With the appliance off and unplugged, take a gander at the pump for visible debris and obstructions.
Advanced Tip: The pump motor might need professional repair or replacement if it is not working.
5. Ensure Proper Alignment
Check that the dishwasher is level using a spirit level; adjust the legs if necessary. Double-check that nothing obstructs the path of the drain hose or the door seal.
6. Restart the Dishwasher
After addressing the possible causes, turn on the dishwasher and check whether the error code disappears. Run a short wash cycle in order to check whether the issue in the draining has been resolved.
When to Call a Professional
If all of the aforementioned steps have been attempted and the error code continues, this may be a time to seek expertise. The origin may involve a higher order of a mechanical or electrical failure that could necessitate access to specialized equipment or expertise.
Contact Cove customer support for a heads up, or arrange a visit by one of their certified professionals.
Preventing Error Code 800140 in the Future
To avoid running into drainage issues in the future, try the following preventive measures:
- Regularly clean the drain filter (once a month is ideal).
- Pre-rinse dishes to remove large food particles.
- Use high-quality dishwasher detergent to prevent residue build-up.
- Make sure the dishwasher is installed correctly and remains level.
Final Thoughts
While the Cove dishwasher error code 800140 can feel frustrating at first, it’s often a solvable issue with a bit of patience. By understanding its causes and following the troubleshooting steps, you’re likely to save yourself a potentially costly service call.
Still need help? Our community of dishwasher enthusiasts is here to support! Leave a comment or share your experience below.
And remember-sometimes the best times come well after the mess has been cleaned up. Keep your machine purring, and it’ll do all the work for you.