SMEG Dishwasher 5 Beeps then Stops​

Smeg Dishwasher-What does it mean by 5 Beeps? Troubleshooting

Have you ever turned your Smeg dishwasher on, only to get five beeps and then. nothing? If this sounds all too familiar, you are not alone. Whether it be in the middle of a busy schedule or during dinner parties, when your dishwasher stops without prior notice, frustrations are sure to set in. Don’t worry, though-those five beeps are actually your dishwasher’s distress signal, and decoding it is easier than it seems.

In this guide, we walk you through what the beeps mean, why they are happening, and how to fix the problem-no panic required.

What Are the 5 Beeps Trying to Tell You?

Almost all the latest dishwashers, such as Smeg, are designed with diagnostic systems. These usually warn users about possible failures through error codes or specific sequences of beeps.

In the case of an Smeg dishwasher, a series of five beeps followed by machine silence indicates a faulted signal that requires attention before anything else for the cycle to continue. While the specific cause may vary between models, five beeps often point to one of the following common issues:

Water does not drain out of the dishwasher. Filter clogged: It could be because of some blockage within the filter or a collection of debris inside it.

Insufficient water supply: The dishwasher is not getting enough water for its functions. Sensor fault or electrical fault: Something wrong with the sensors of the machine or its electrical circuitry. All these have pretty easy solutions which you can try before calling a technician.

Step-by-Step Troubleshooting for Your Smeg Dishwasher

Step 1. Check the Drainage System

If your Smeg dishwasher can’t drain water as required, the machine will simply stop mid-cycle to prevent flooding. Here’s how to check for drainage issues:

Check the drain hose. Is it kinked, blocked, or was it badly installed? Straighten any bends and make sure the hose is unobstructed. Pump Clearance: Check visibly for blockages and remove the debris in that area.


Check Connection: Make sure that the dishwasher drain is properly and securely connected with your house’s plumbing.
Run another cycle and check again. If still getting five beeps, continue to step 2.

Step 2. Filter Clean

Food particles or hard water may block the filter of the dishwasher and make it malfunction. Fortunately, this can be cleaned quite easily and pretty fast:

Switch the power off and take out the lower spray arm. Pull out the filter, which is generally located at the bottom of the dishwasher. Rinse the filter under warm water and gently scrub with a soft brush. Place the filter back and secure it tightly. This can be avoided by cleaning detergent and disposal of food regularly.

Dishwasher Smells Bad

Step 3. Check the Water Supply

Dishwashers require uninterrupted water supply to complete cycles. Here is how to go about it.

Water Line: The hose should not have blockages, twists, or leaks. Change the Valve: Ensure that the water valve that supplies water to your dishwasher is fully turned on.

Check the Water Pressure: Low water pressure can also trigger the error. You may want to test other appliances to confirm water pressure to your home. In many cases, stable water flow can resolve the beeping issue.

Step 4. Examine Sensors and Electrical Components

If the above steps don’t yield results, the issue may lie with the dishwasher’s internal sensors or electronics:

Clear any obstruction from the float switch: It monitors the water level inside. Damage or loose control panel connections also need to be checked. If you’re comfortable doing it, unplug the machine to reset its electronic system for at least 10 minutes. If you suspect electrical or sensor malfunctions deeper within, it is probably time for professional repair.

How to Avoid Issues in the Future

Maintenance is key to keeping your Smeg dishwasher running smoothly. Here’s what you can do to avoid more five-beep interruptions in the future:

Clean the Filter Regularly: A monthly rinse can prevent clogs from forming. Run a Descaling Agent: Hard water can cause mineral buildup, so clean your dishwasher with a descaling solution every few months.

Run the dishwasher with only dishwasher-safe items, as many of these can leave residues that clog filters and internal parts. Yearly Checks on Hoses: Check the water supply and drain hoses to ensure they are not damaged and are properly aligned. A few proactive steps can save you time, money, and frustration further down the line.

When to Call in Professional Help

While Smeg dishwashers are fantastic appliances, some problems may require expert assistance. If you’ve tried all the troubleshooting steps above and your dishwasher is still stuck in the five-beep cycle, contact Smeg customer support or a qualified technician.

When calling for help, have the five-beep error in mind and mention the model number of your dishwasher. This can help speed up diagnosis to get your appliance back into service sooner.

Don’t Panic Smeg’s Got Your Back

While the five beeping sounds from a dishwasher can become a real pain, very often, they are pretty simple to fix. From a clogged filter to water supply checks to resetting the system, the steps one would go through before calling in a professional end.

With a little maintenance and attention, your Smeg dishwasher will soon be back to delivering sparkling-clean dishes. Have additional questions about dishwasher care or other appliance tips? Drop a comment below we’re here to help!

Click to rate this post!
[Total: 0 Average: 0]
Spread the love