Fisher and Paykel is a well-known brand of home appliances, and their dishwashers are particularly popular. However, like all electronic devices, these dishwashers can experience errors and malfunctions. Fisher and Paykel dishwashers are equipped with error codes to help users diagnose and troubleshoot any problems that arise. In this article, we will take a closer look at Fisher and Paykel dishwasher error codes, what they mean, and how to resolve them.
Understanding Fisher and Paykel Dishwasher Error Codes Fisher and Paykel dishwashers use a variety of error codes to help users identify problems with their machines. The error codes are usually displayed on the dishwasher’s control panel. Here are some common Fisher and Paykel dishwasher error codes and their meanings:
Error Code | Issue | Solution |
---|---|---|
A-Series Error Codes | ||
A1 | No Water Supply |
• Check water valve is open • Ensure adequate water pressure • Inspect inlet hose for kinks or blockages |
A3 | Drainage Issue |
• Check drainage hose for obstructions • Inspect connection to drainage pipe |
A6 | Loose Spray Arm or Foaming Issue |
• Ensure spray arm is properly attached • Use only recommended dishwasher tablets |
A7 | Excess Foam Detected |
• Use only dishwasher-approved detergent • Run empty cycle to clear foam buildup |
A09 | Sanitize Cycle Failure (DD*C Models) |
• Ensure hot water supply is set to at least 65°C (149°F) • Avoid overloading the dishwasher |
A10 | Water Supply Issue |
• Turn on water tap • Check for low water pressure or kinked inlet hose |
A20 | Drainage Fault |
• Inspect and clear blockages in drain hose • Check outlet connection for clogs |
A60 | Water Temperature Error |
• Turn dishwasher off and on again • Contact customer care if error persists |
AD0 | Door Lock Signal Error |
• Restart dishwasher • Seek professional service if issue remains |
F-Series Error Codes | ||
F1 | Flood Detected |
• Turn off water and power supply • Call for service if issue persists |
F2 | Motor Rotor Fault | Remove any blockages and restart |
F3 | Temperature Sensor Fault |
• Ensure incoming water is below 65°C (149°F) • Install tempering valve if needed |
F4 | Heating Element Fault | Check heating element and replace if faulty |
F5, F6, F7 | Lid Faults |
• Turn power off and on again • Ensure lid closes properly |
F8 | Electrical Problem |
• Restart dishwasher • Call for service if unresolved |
F9 | Electronics Malfunction | Restart the unit |
F30 | Flood Switch Activated | Turn off power and water, then call for service |
F40, F50, F90 | Electronics Errors |
• Restart dishwasher • Contact customer care if problem persists |
FA0 | Power Supply Error | Turn dishwasher off and on again |
FC0 | Motor Fault |
• Restart unit • Call customer care if unresolved |
U-Series Error Codes | ||
U1 | Fill Fault |
• Ensure water supply is turned on • Make sure spray arm is properly attached |
U2 | Loading Issue | Rearrange dishes that extend beyond drawer height |
U4 | Drawer Fault | Restart the unit |
U6 | Spray Arm Issue |
• Secure spray arm in place • Ensure water pressure is sufficient |
E-Series Error Codes | ||
E1 | Flood Detected | Turn off water and call for service |
E2 | Motor Rotor Fault | Clean and inspect rotor for debris/broken glass |
E3 | Temperature Sensor Fault | Ensure water supply temperature is below 65°C (149°F) |
E4 | Heating Element Failure | Inspect and replace heating element if needed |
E5 | Lid Motor Fault | Restart the dishwasher |
E6 | Drying Fan Fault | Check and replace drying fan if necessary |
E7 | Detergent Dispenser Electronics Fault | Restart the unit |
E8 | Electronics System Fault | Contact customer care for repairs |
E9 | Controller Electronics Fault | Restart the dishwasher |
EC | Communication Error Between Drawers | Restart the dishwasher |
How to Reset Your Fisher & Paykel Dishwasher
- Turn off the dishwasher for at least 30 seconds
- Check water supply & drainage – ensure hoses are clear and valves are open
- Inspect spray arms & filters for blockages
- Power the unit back on and check if the error persists
- F1: This error code indicates a problem with the dishwasher’s flood switch. The flood switch is a safety feature that detects when the dishwasher is leaking water. If the switch is triggered, the dishwasher will stop working to prevent further damage. To resolve this issue, check the dishwasher’s bottom for any signs of leakage, and ensure the dishwasher is level.
- F2: The F2 error code indicates a problem with the dishwasher’s motor or motor control circuit. If you receive this error code, the dishwasher may be unable to run or complete its cycle. To resolve this issue, you may need to replace the dishwasher’s motor or control circuit.
- F3: This error code indicates a problem with the dishwasher’s temperature sensor. If you receive this error code, the dishwasher may be unable to regulate its water temperature properly. To resolve this issue, you may need to replace the dishwasher’s temperature sensor.
- F4: The F4 error code indicates a problem with the dishwasher’s water inlet valve. If you receive this error code, the dishwasher may be unable to fill with water properly. To resolve this issue, you may need to replace the dishwasher’s water inlet valve.
- F5: This error code indicates a problem with the dishwasher’s lid. If you receive this error code, the dishwasher may be unable to close properly. To resolve this issue, you may need to adjust the dishwasher’s lid or replace any damaged parts.
- F6: The F6 error code indicates a problem with the dishwasher’s water turbidity sensor. If you receive this error code, the dishwasher may be unable to detect how dirty the water is. To resolve this issue, you may need to replace the dishwasher’s water turbidity sensor.
- F7: This error code indicates a problem with the dishwasher’s heating element. If you receive this error code, the dishwasher may be unable to heat water properly. To resolve this issue, you may need to replace the dishwasher’s heating element.
- F8: The F8 error code indicates a problem with the dishwasher’s drain pump. If you receive this error code, the dishwasher may be unable to drain properly. To resolve this issue, you may need to replace the dishwasher’s drain pump.

FAQs
- How do I reset my Fisher and Paykel dishwasher?
To reset your Fisher and Paykel dishwasher, turn off the dishwasher’s power supply for 5-10 minutes. Then, turn the power supply back on and restart the dishwasher.
- What should I do if my Fisher and Paykel dishwasher is not draining?
If your Fisher and Paykel dishwasher is not draining properly, check the dishwasher’s drain hose and ensure it is not clogged. You may also need to clean the dishwasher’s filter or replace the dishwasher’s drain pump.
- How often should I clean my Fisher and Paykel dishwasher?
It is recommended to clean your Fisher and Paykel dishwasher at least once a month. This will help ensure that the dishwasher is operating efficiently and can help prevent any potential malfunctions or errors.
- How do I clean the dishwasher’s filter?
To clean the dishwasher’s filter, first, remove any large food particles or debris from the dishwasher’s interior. Then, locate the filter at the bottom of the dishwasher and remove it. Rinse the filter under running water to remove any remaining food particles, and then replace it in the dishwasher.
- What should I do if my Fisher and Paykel dishwasher is not washing dishes properly?
If your Fisher and Paykel dishwasher is not washing dishes properly, first ensure that you are using the correct type and amount of detergent. You may also need to clean the dishwasher’s spray arm or check for any clogs in the dishwasher’s water jets.
- Can I repair my Fisher and Paykel dishwasher myself?
While some minor issues with Fisher and Paykel dishwashers can be resolved by the user, more complex issues may require professional repair. If you are unsure about how to troubleshoot or repair your dishwasher, it is best to consult a qualified technician.
Conclusion
Fisher and Paykel dishwashers are reliable and efficient appliances, but they can experience errors and malfunctions over time. By understanding the various error codes and troubleshooting steps, users can diagnose and resolve most issues that arise. Regular maintenance, including cleaning the dishwasher’s filter and checking for clogs, can also help prevent potential problems. If you encounter a persistent issue with your Fisher and Paykel dishwasher, it is best to seek the advice of a professional technician.
Pingback: Fisher Paykel Dishwasher Troubleshooting: Tips for Fixing Common Issues