Table of Contents
What to Do About Haier Dishwasher Error 17
Dishwashers have made household chores so much easier, turning mountains of dishes into a quick and easy chore. But what does one do when it gives an error code and not sparkling clean plates? If your Haier dishwasher is kicking up “Error 17,” well, you must be utterly confused and frustrated. Don’t worry, you aren’t the only one, and we are here to help you figure it out.
What Does Haier Dishwasher Error 17 Mean?
Error 17 may sound ambiguous, but it’s Haier’s way of telling you there is an issue with the lower water levels inside your dishwasher. In other words, the system thinks it’s not getting enough water to function correctly. But this could be due to one of many issues, and diagnosing it doesn’t necessarily need a professional’s expertise right away.
Think of it this way—just like a car gives you a warning light on the dashboard when it is running low on fuel, this dishwasher is giving that flashing red light to show that something in its water system is not flowing as it should.
Why Does This Happen? Common Causes of Error 17
There are a few common culprits behind this error. So, before you freak out or think about getting your dishwasher replaced, here are a few suspects:
Water Supply Issues
Sometimes the most obvious explanation is the right one. Check that the water supply to your dishwasher is turned on. A kink in the hose leading from the water supply to the dishwasher, a turned-off water valve, or low water pressure from your tap can all cause the error.
Clogged or Dirty Filter
Over time, food particles, grease, or debris can clog your dishwasher’s filter or water inlet valve, restricting the water flow. If it’s been a while since you’ve cleaned your dishwasher’s filter, this could be the source of the problem.
Blocked Spray Arms
The spray arms disperse water in your dishwasher during a cleaning cycle. If they become clogged or jammed with debris, the dishwasher may not reach the required levels of water.
Faulty Water Level Sensor
Your dishwasher uses sensors to detect the level of water at all times. If any one of them malfunctions or provides a faulty reading of the levels inside the appliance, then Error 17 would be initiated for no good reason on the supply side.
Defective Drain Pump
A clogged or a poorly operating drain pump will limit the proper cycling of water within the appliance, hence a low water error response.
How to Fix Haier Dishwasher Error 17
The fix for this error may be much easier than you think it will be, depending on what the cause is. Here’s how you can do this:
1. Check the Water Supply
- Make sure your water valve is turned on full.
- Check the supply hose for kinks or blockages.
- If the water pressure in your house seems a little low, then you may need to have a plumber take a look.
2. Clean the Filter
- At the bottom of your dishwasher, there is usually a filter that should be twisted and pulled out for easy cleaning.
- Wash it under running water and, with the aid of a soft brush, remove any gunk in it.
- Let this be replaced with security afterward to avoid potential mistakes later on.
3. Inspect the Spray Arms
- Spray arms should be removed and washed thoroughly, making sure each piece of debris inside the holes is worked out with a toothpick because this blocks water.
- Attach these on securely and check for easy water flow during the cycle.
4. Test the Water Level Sensor
- If you suspect that it might be faulty, then refer to your Haier dishwasher manual for instructions on how to reset or replace it.
- If that sounds a little more than what you’re comfortable with, this could be one of those times where calling a professional is in order.
5. Clear the Drain Pump
- Check the drain pump for blockages. Sometimes, small pieces of food or even glass can obstruct this from working right.
- Cleaning the pump may require removing the lower panel of your dishwasher, so be careful or seek the help of a professional in that regard.
6. Restart Your Dishwasher
- After any of the above fixes, unplug your dishwasher for a few minutes and plug it back in to reset the system.
- Sometimes this may clear the error and allow normal operation to resume.
When to Call in an Expert
If you’ve gone through all these steps and the error persists, it may be time to contact Haier’s customer service or a certified repair technician. While Error 17 is often linked to minor water flow issues, some internal components might require replacement. Keep in mind that many Haier dishwashers come with a warranty, so be sure to check your documentation before paying out-of-pocket for repairs.
Preventing Future Error 17 Issues
The secret to a healthy dishwasher is maintenance. Here are some tips that will help your Haier dishwasher run smoothly:
- Clean the filter routinely: Make it a habit to rinse the filters monthly to avoid blockages.
- Wipe down the spray arms: Check for blockages every few weeks and clean them as needed.
- Check on water hoses: Every six months, take some time to check the supply and drain hoses for wear and leakage signs.
Applying these minor maintenance steps can significantly lower the possibility of an Error 17, or any other error, ever reappearing again.
Conclusion
Haier Dishwasher Error 17 can be a real pain, but it doesn’t have to knock your whole day off kilter. In most instances, this is usually something as minor as issues to do with water flow or giving your dishwasher a little TLC. If in doubt, though, this is something the professionals should handle, who will see to it that things get back on track in no time.
Any trouble with the dishwasher or simply interested in household appliances care? Leave your questions in the comments, and we’ll try our best to answer them!