Table of Contents
Troubleshooting the Hotpoint Dishwasher F2 Error Code
An F2 error code in your Hotpoint dishwasher simply means it has reached its limit, and you are left in a dilemma, not knowing what to do. The F2 error code isn’t as scary as it sounds, and by being methodical, you can find the problem and fix it to get back to an efficient, time-saving dishwasher. This post will explain what the F2 error code means, the causes of this error code, and detailed, step-by-step troubleshooting methods.
What does the Hotpoint dishwasher error code F2 mean?
The F2 error code on a Hotpoint dishwasher normally signals some problem in drainage. More precisely, it means that water cannot be drained out of the unit properly. This could be due to one or more causes ranging from blockages to malfunctioning pumps or sensors.
Being aware of the root cause is the first step toward properly addressing the situation.
Typical causes behind an F2 display on Hotpoint dishwashers are the many that could well stem from diverse regions of the washer. The ensuing describes most of the familiar ones:

The drain hose obstructs
The F2 code primarily, due either to debris issues, kinking, or actual deposits inside – everything restricts flow and thereby culminates into such an error
Clogged filters
Filters are supposed to catch food particles and debris in a dishwasher. These may cause a clog in the drainage since they are not regularly cleaned.
Deteriorated Drain Pump
The drain pump is designed to pump water out of the dishwasher. It will not be able to do its job properly when it has gone faulty and may not drain enough water.
Clogged Sump Area
The sump is responsible for the collection of water before it gets drained out. When this section gets blocked with food chunks or any other type of sediment, there arises the F2 error.
Faulty Sensor
Some Hotpoint dishwashers use sensors for detecting the level of water and the kind of drainage. A malfunctioning sensor might give a faulty indication of faulty drainage and, hence will flash the F2 code.
How to Fix F2 Error Code
Here is the step-by-step procedure to diagnose and fix the problem:
1. Switch Off and Unplug the Dishwasher
Before starting any repair or check, switch off and unplug the dishwasher from the power source. This will avoid any possibility of electric shock.
2. Check the Drain Hose
The drain hose may be blocked, kinked, or damaged. Here’s how: Find the drain hose that’s usually attached to the rear of the dishwasher and reaches over to your kitchen sink or garbage disposal. Remove the hose and run some water through it to see if the problem is a blockage. If so, clean out the blockage with a pipe cleaner. Reattach, making sure the hose is connected and not kinked.
3. Clean the Filters
The filters in the dishwasher need regular cleaning. Here’s how: Refer to your Hotpoint dishwasher manual to find where the filters are-actually situated at the bottom of your appliance. Remove the filters and clean them under running water to remove grease or food particles. If the filters are severely clogged they should be soaked in soapy, warm water before being rinsed.
4. Check the Drain Pump
If this does not work, it may be time to check the drain pump: Gain access to the drain pump by removing the bottom panel of your dishwasher. Refer to your manual for instructions. Look inside the pump for blockages or debris, and clean out carefully. If it is seriously damaged or doesn’t work after cleaning, then it should be replaced.
5. Clear the Sump Area
The sump area may also be blocked: Use a flashlight to inspect the sump, which is usually located at the bottom of the dishwasher. Carefully remove any food particles or debris that could be obstructing water flow.
6. Test the Dishwasher
After performing these checks and fixes, reconnect the dishwasher to the power source and run a rinse cycle. Monitor the machine to ensure the F2 error code does not reappear.
When to Call a Professional
If you have gone through the above process and the error persists, then it’s time to call a professional technician. It may be due to a more intricate problem such as malfunctioning wiring, a faulty sensor, or even a pump replacement that requires more specialized tools and expertise.
Also, if your dishwasher is still under warranty, reaching out to Hotpoint’s customer service is highly recommended.

Tips to Avoid F2 Errors in the Future
Regular maintenance can help prevent drainage issues and extend the lifespan of your Hotpoint dishwasher. Here are some tips to keep in mind:
- Clean the filters once a week to prevent clogs.
- Avoid overloading the dishwasher, as it can lead to blockages in the sump area.
- Scrape off excess food from dishes before loading them into the dishwasher.
- Periodically check the drain hose and clean it if necessary.
- Run a monthly cleaning cycle using a dishwasher cleaner to clear out grease and grime.
Wrapping Up
Encountering an F2 error code on your Hotpoint dishwasher can be frustrating, but it’s a problem that can often be resolved with basic troubleshooting steps. By identifying and addressing the root cause, you’ll not only fix the issue but also improve the overall performance of your appliance.
If all the above steps have been tried and the problem persists, don’t hesitate to consult a professional. And remember, routine maintenance will go a long way toward preventing future hiccups, keeping your dishwasher running smoothly for years to come.