Ignis Dishwasher Fault Codes

Understand Your Ignis Dishwasher Error Codes- The Correct Solutions

Most times when an Ignis dishwasher flashes up its fault code, the primary urge will be one of fear and desperation. Relax. Those are created to better guide you towards understanding why it fails to act appropriately and consequently repair or service appropriately. Some minor repairs could possibly be performed independently. More difficult and critical repairs shall demand a visit by an Ignis-approved repair engineer.

Below, I will take you through all the possible Ignis dishwasher error codes, what they mean, and what you can do to get your dishwasher back up and running.

Why Ignis Fault Codes Are Useful

Fault codes may look intimidating, but they are actually there to help. They give you diagnostic information about your dishwasher’s health, which can help you pinpoint specific problems rather than just guessing. While some errors require a technician to come and sort out the problem, others can be fixed by doing a quick DIY fix.

The Complete List of Ignis Dishwasher Fault Codes

Here’s every Ignis fault code currently in use, along with instructions on what they mean and how to address them:

Ignis Dishwasher Fault Codes

Understand Your Ignis Dishwasher Fault Codes – The Correct Solutions

When your Ignis dishwasher displays a fault code, don’t panic! These codes help diagnose problems. Some can be fixed easily, while others may require a professional.

The Complete List of Ignis Dishwasher Fault Codes

Fault Code Meaning Solution
E1 Water Supply Fault Check the water tap, inlet hose, and supply valve.
E2 Drainage Fault Inspect the drain hose, filter, and connected sink drain.
E3 Heating Fault Ensure the dishwasher isn’t overloaded, inspect heating element.
E4 Water Overfill Check for leaks, inspect float switch and inlet valve.
E5 Door Not Closed Properly Ensure the door is latched; check door switch alignment.
E6 Faulty Water Sensor Clean the water sensor; replace if necessary.
E7 Motor Fault Clear debris around the motor; call a technician if damaged.
E8 Spray Arm Fault Clean spray arms and remove blockages.
E9 Electronic Controller Fault Reset the dishwasher; if error persists, call a technician.
EA Aquastop Activated Check for leaks, dry the base pan, call professional if needed.
EB Communication Fault Inspect wiring and connections; replace damaged parts.
EC Pressure System Fault Clean pressure sensor, check water lines for blockages.

E1 – Water Supply Fault

What it means: Your dishwasher can’t fill up with water. It is probably a problem with the water supply.

How to fix it:

  • Make sure the water tap is fully turned on.
  • Check the inlet hose for kinks or blockages.
  • Check the water supply valve to ensure it’s not faulty.

E2 – Drainage Fault

This essentially means that water is not draining out of your dishwasher properly.

How to troubleshoot:

  • Check the drain hose for blockages or bends.
  • Remove blockages in the filter and pump area in your dishwasher.
  • Clear the sink or drain your dishwasher is connected to.

E3 – Heating Fault

What it means: Water in your dishwasher doesn’t warm up and might be caused by a defective heating element.

How to fix it:

  • Ensure your dishwasher isn’t overcrowded because that could be hindering its operation.
  • Inspect the heating element or get a professional technician to see whether the element is defective and should be replaced.

E4 – Water Overfill

What it means: Your dishwasher has sensed excessive water, probably due to a leak or worn out water inlet valve.

How to fix it:

  • Inspect the appliances for visible leaks
  • Check the float switch is operating freely
  • Clean the inlet valve and ensure proper sealing.

E5 – Door Not Closed Properly

What it means: The door is not closed well, or the door switch is faulty.

How to fix it:

  • Make sure the door is closed and latched.
  • Check the door switch for any damage or misalignment.

E6 – Faulty Water Sensor

What it means: There is an error with the water level sensor, which makes your dishwasher give wrong readings.

How to fix it:

  • Clean the water sensor because build-up or debris often causes malfunctions.
  • If the problem persists, the sensor may need to be replaced.

E7 – Motor Fault

What it says: The main wash motor is defective. Blockage or mechanical failure may cause this fault.

How to troubleshoot:

  • Clean the motor or its surrounding area of debris
  • Have a professional technician repair it in case the motor seems damaged

E8: Spray Arm Fault

What it means: The spray arms cannot operate their usual motion; the end result is an ineffective cleaning job

How to troubleshoot:

  • Clean the spray arms and make sure all the holes are not blocked.
  • Check for blockages that may prevent them from spinning freely.

E9 – Electronic Controller Fault

What it means: This code usually indicates a problem with the control board or wiring.

How to troubleshoot it:

  • Reset the dishwasher by turning it off for a few minutes, then turn it back on.
  • If the error persists, call a technician for diagnostics and repair.

EA – Aquastop Activated

What it means: The anti-flood system has been activated due to a leak or an overflow.

How to fix it:

  • Switch off the water supply and unplug the dishwasher.
  • Check the base pan for water. If there is water, dry it before restarting.
  • If leaks persist, call for professional assistance.

EB – Communication Fault

What it means: There’s a communication error between the dishwasher’s components, such as the control board and sensors.

How to fix it:

  • Check the wiring and connectors for any damages or loose connections.
  • For hardware that is visibly damaged, call a service technician.

EC – Pressure System Fault

Meaning: The control system of the house’s water supply pressure is not working.

Step to troubleshoot:

  • Clean all parts associated with the pressure sensor.
  • Check to ensure there is no blockage in the house’s water lines or hoses.

Bonus Tip: How to Reset Your Dishwasher

Sometimes, a number of problems can be solved by resetting. Unplug your dishwasher, and let it sit for about 10 minutes before plugging it back in. This will usually clear minor glitches and allow your unit to recalculate.

When to Call for Professional Help

While some of these faults can be easily rectified, others require a professional hand. If the troubleshooting doesn’t get your dishwasher running, or if the error code continues to reappear, it’s best to consult an appliance technician.

Some Precautions to Keep Your Ignis Dishwasher

Some of the common faults can be prevented by carrying out some of the basic preventive measures for your Ignis dishwasher. This can possibly prolong the lifespan of your dishwasher.

  • Clean the filters, spray arms, and drain hoses regularly to avoid build-up.
  • Use the recommended detergent and rinse aid by Ignis.
  • Do not overload your dishwasher; arrange dishes to avoid any blockages.

Final Thoughts

While it’s frustrating to see your Ignis dishwasher flashing a fault code when dinner dishes are piling up, these fault codes are your first clue into diagnosing the problem. You can understand what each fault means and follow the respective troubleshooting steps to solve most of them very rapidly and efficiently.

If it doesn’t work, don’t hesitate to call for a professional. After all, a working dishwasher ensures that your process is stress-free and who doesn’t love that?

Still got questions about the maintenance or repair of your dishwasher? Leave it in the comments below!

Click to rate this post!
[Total: 0 Average: 0]
Spread the love