Indesit Dishwasher Flashing Lights 1 and 3

What Does it Mean if Your Indesit Dishwasher is Flashing Lights 1 and 3?

When your Indesit dishwasher lights 1 and 3 flashing​, you will most likely feel anything but quite happy. After all, dishwashers are created to make things easier around the house.

The good news is that this blinking light pattern acts as your dishwasher’s way of trying to communicate with you to say something has gone wrong, and the fix usually is way easier than one would imagine. This guide helps you understand what is going on and walks you through the steps to fix this problem.

What does it mean when lights 1 and 3 flash?

If your Indesit dishwasher shows blinking lights of the first and third indicators, then such a situation signals an error in water drainage. In fact, your dishwasher is not draining water during or at the end of a wash cycle. This can be because of blockages, problems with the pump, and sometimes an electronic glitch.

But don’t freak out-we are here to guide you through some troubleshooting that should get your dishwasher back in working order without the need for an expensive technician.

How to Fix Lights 1 and 3 Flashing-Step-by-Step Guide

Follow these easy steps to diagnose and fix the problem easily:

1. Switch Off the Dishwasher

Before you start any troubleshooting with your dishwasher, make sure it is switched off and unplugged. This is for your safety while investigating the problem.

2. Check the Filter

Often, the cause of a drainage issue is a clogged filter. Here’s how to check it:

  • Open the dishwasher and remove the bottom rack.
  • Locate the filter at the base; it’s usually easy to spot.
  • Carefully remove the filter and rinse it under warm water. Use a brush to clean off any stubborn debris, such as grease or food particles.
  • Once it’s clean, replace the filter securely.
Dishwasher Smells Bad

3. Inspect the Drain Hose

Check blockages or kinks in the drain hose:

  • Identify the hose normally situated at the back of the dishwasher and is usually connected with either the sink or a waste disposal.
  • Remove the hose and check for blockages. If clogged, run water through the hose or snake it.
  • Look for twists or bends in the hose that would hinder any flow of water through.
dishwasher hose

4. Check Sink Drain for Clogs

Sometimes your dishwasher’s problem is your sink. If the drain in your sink or your garbage disposal is clogged, then water from the dishwasher has no place to go.

  • Run some water in the sink to see if it drains freely.
  • If not, use a plunger, drain cleaner, or a plumber to clear out any obstruction that’s preventing draining.

5. Check the Pump

If the filter and drain hose are clean, and the problem persists, the drain pump may be the cause:

  • Locate the drain pump. If you are unable to tell where it is, check your dishwasher manual.
  • Remove the cover of the pump and inspect for blockages or debris.
  • If you find that the pump is damaged or worn out, you may have to replace it.

6. Reset Your Dishwasher

This could be an electronic glitch if there is no visible blockage or damage. Reset your dishwasher by doing the following: Plug it back in, then hold down the start/reset button for a few seconds. Wait a moment before starting a new cycle to see if this resolves the problem.

7. Call a Professional

If no such steps help in solving this problem, it’s probably now time to involve a professional; it might as well be that something inside-the internal part at the control board-is what a professional repair alone can fix.

Tips to Avoid Future Drain Issues

A little maintenance will do a great way in making your Indesit dishwasher serve for years to come. Herein comes how you can avoid this and similar kind of problems in the future.

  • Clean the Filter Regularly: Make it a habit to clean your dishwasher filter every 1–2 weeks to avoid buildup.
  • Scrape Food Off Plates: While your dishwasher will be able to take small food particles, it is not designed to take in larger scraps that may clog the system. Scrape or quickly rinse your dishes before placing them inside the appliance.
  • Keep the Drain Hose Clear: Check the drain hose for blockages or kinks at routine maintenance.
  • Run the dishwasher cleaner or vinegar through the cycle once a month to dissolve grease and limescale buildup.

Conclusion

Blinking lights can be a pain in the neck, but they are your Indesit dishwasher’s way of telling you that something is wrong. If you have gone through the above steps, then you are pretty much guaranteed to fix it yourself-and save both time and money.

But remember, you’re not in this alone. If you’re still experiencing trouble, don’t hesitate to call a professional for support. With proper care and maintenance, your dishwasher will work like a champ for years to come.

Got questions or your own tip to share? Leave a comment below!

Click to rate this post!
[Total: 0 Average: 0]
Spread the love